exhaust manifold

1. The exhaust gas exits through the other exhaust manifold.
   废气经另外一个排气歧管排出。
2. A valve through which burned gases from a cylinder escape into the exhaust manifold.
   通过来自汽缸的燃烧废气进入排气集管的阀。
3. Fasten primary catalytic converter to the exhaust manifold.
   将初级催化转化器紧固到排气歧管。
4. High temperature oxidation cracking analysis of exhaust manifold made of high Si-Mo nodular cast iron
   高硅钼球铁排气歧管高温氧化开裂原因分析
5. Lay the oxygen sensor cable so that it cannot touch the exhaust manifold.
   布置好氧传感器电缆，使其远离排气歧管。
6. Exhaust manifold, Vibration, Finite element method;
   排气总管，振动，有限单元法；
7. Secure triangular flange for exhaust manifold using three new M8 lock nuts.
   用三个新的m8锁紧螺母固定排气歧管的三角法兰。
8. A pipe through which burned gases travel from the exhaust manifold to the muffler.
   一种经此燃烧气体将从排气集管排放到消声器的装置。
9. Turbochargers can be mounted to its own exhaust manifold but on inline engines, both turbos can be mounted on the same manifold.
   涡轮增压器可以安装到自己的排气歧管但直列发动机上，都可以安装增压器在同一在静听着的松林之间。
10. The exhaust manifold, the silencer, and the charge-air cooler display the logo of the world famous customizer from Bavaria.
    在排气的消声器和空气冷却器显示，世界著名的标志从巴伐利亚定制。
11. The basic exhaust system consists of an engine exhaust manifold, exhaust pipe, exhaust heat shield ( s), muffler and exhaust tailpipe
    基本排气系统包括一个引擎排气歧管、排气管道、排气隔热罩、消音器和排气尾管
12. CFD& FEA coupling analysis application in exhaust manifold analysis
    某发动机排气歧管流固耦合分析的应用
13. The obligating space on the hole makes the exhaust manifold having enough space when deforming and preventing cutting out the bolt even the exhaust manifold is deformed.
    安装孔的预留空间使得在歧管变形时留有足够的变形空间，即使排气歧管变形也不会剪断通过安装孔的螺栓。
14. Install cylinder head, intake manifold, and exhaust manifold, refer to cylinder head installation in this section.
    安装汽缸盖，进气歧管和排气管，请参阅本部分的汽缸盖安装。
15. Unscrew all fastening nuts between primary catalytic converter and exhaust manifold.
    旋下初级催化转化器与排气歧管之间所有的紧固螺母。
16. Check for signs of leakage or cracked surfaces at both ends of tube, exhaust manifold and EGR valve.
    检查两个管的末端，排气歧管和EGR阀是否有泄露或表面有裂痕。
17. Loosen starter catalyst from exhaust manifold.
    从排气歧管上松开起动机催化剂。
18. Clean the exhaust manifold and cylinder head mating surfaces.
    清洁排气歧管和汽缸头配合面。
19. The beading is facing the exhaust manifold and the edges must not project over the contour of the flange.
    涂条朝向排气歧管且边缘不能探出法兰的轮廓。
20. It was studied that the reason of fatigue-broken of the exhaust manifold resulted from vibration in a diesel engine using FEA and FE-SAFE software.
    运用有限元法和疲劳分析FE-SAFE软件对某型柴油机排烟管由于振动引起的疲劳断裂原因进行了研究。
21. Couple CFD-FE-Analysis for a Gasoline Engine Exhaust Manifold of Thermal Load
    CFD-FE耦合计算分析某汽油机排气歧管热负荷
22. Fit oxygen sensors ahead of catalytic converter at the exhaust manifold.
    安装排气歧管处催化转换器前的氧传感器。
23. Study on Flow Field Analysis and Structure Optimization of Exhaust Manifold Catalytic Converter
    歧管式催化转化器流场分析及结构优化研究
24. Tighten exhaust manifold to cylinder head bolts.
    紧固排气岐管汽缸头螺栓。
25. The modified pipe guide on the exhaust manifold has also resulted in a significantly improved torque.
    排气歧管上导管的改进还使扭矩得以显著改善。
26. Exhaust manifold heat control valve
    排气歧管热量控制阀
27. Always replace exhaust manifold screws during installation.
    务必在安装时更换排气歧管螺钉。
28. The thermal stress of internal combustion engine exhaust manifold was calculated with the fluid-structure coupled simulation.
    采用流固耦合方法计算了内燃机排气歧管的热应力。
29. The thermal fatigue failure of the new exhaust manifold was eliminated.
    对原方案提出了改进意见，结构改进后，排气歧管热疲劳失效得到排除。
30. Then, I simulated the exhaust manifold under the condition of real working flow capacity of engine.
    接着又对排气歧管在实际发动机工作时的流量条件下进行了模拟计算。

noun

1. a manifold that receives exhaust gases from the cylinders and conducts them to the exhaust pipe